Difference between revisions of "DEWBOT VII Week Five Build Season Photo Gallery"
From DEW Robotics
MaiKangWei (talk | contribs) (→Tuesday February 8, 2011) |
|||
(17 intermediate revisions by 3 users not shown) | |||
Line 40: | Line 40: | ||
Image:DB7_Selina_110208_csm.jpg|Selina installing treads on wheels | Image:DB7_Selina_110208_csm.jpg|Selina installing treads on wheels | ||
Image:DB7_Deaver_Melanie_Faith_Matt_110208_csm.jpg|Gary Deaver, Melanie, Faith McKown & Matt - Materials lab is about to begin | Image:DB7_Deaver_Melanie_Faith_Matt_110208_csm.jpg|Gary Deaver, Melanie, Faith McKown & Matt - Materials lab is about to begin | ||
− | Image:DB7_Matt_carbon_fiber_110208_csm.jpg|Matt filling | + | Image:DB7_Matt_carbon_fiber_110208_csm.jpg|Matt filling end of replacement 1" pultrusions with carbon fiber & epoxy |
Image:DB7_sensor_mount_110208_csm.jpg|Angle sensor mount | Image:DB7_sensor_mount_110208_csm.jpg|Angle sensor mount | ||
Image:DB7_DJ_Featherman_110208_csm.jpg|DJ & Scott Featherman wiring | Image:DB7_DJ_Featherman_110208_csm.jpg|DJ & Scott Featherman wiring | ||
Line 52: | Line 52: | ||
==Wednesday February 9, 2011== | ==Wednesday February 9, 2011== | ||
<gallery widths=250 heights=250 perrow=3> | <gallery widths=250 heights=250 perrow=3> | ||
− | Image: | + | Image:DB7_Andrew_Sasha_110209_csm.jpg|Andrew & Sasha CAD the Minibot |
+ | Image:DB7_Deaver_Ian_110209_csm.jpg|Gary Deaver & Ian laying out carbon fiber on electrical panel | ||
+ | Image:DB7_Rizzo_110209_csm_1.jpg|Mike Rizzo liberating a compressor from [[DEWBOT V]] | ||
+ | Image:DB7_Rizzo_110209_csm_2.jpg|Who mounted this compressor? | ||
+ | Image:DB7_driving_110209_csm_1.jpg|DEWBOT VII's first drive | ||
+ | Image:DB7_driving_110209_csm_2.jpg | ||
+ | Image:DB7_pultrusion_110209_csm.jpg|Pultrusion columns ready for drilling | ||
+ | Image:DB7_epanel_fab_110209_csm_1.jpg|Electronics Panel fabrication | ||
+ | Image:DB7_pully_110209_csm.jpg|Pulley on arm | ||
+ | Image:DB7_epanel_fab_110209_csm_2.jpg|Electronics Panel in the bag | ||
+ | Image:DB7_epanel_fab_110209_csm_3.jpg|Electronics Panel under vacuum | ||
+ | Image:DB7_epanel_fab_110209_csm_4.jpg|Electronics Panel in the easy-bake oven | ||
</gallery> | </gallery> | ||
==Thursday February 10, 2011== | ==Thursday February 10, 2011== | ||
<gallery widths=250 heights=250 perrow=3> | <gallery widths=250 heights=250 perrow=3> | ||
− | Image: | + | Image:DB7_Deaver_panel_110210_csm_1.jpg|Gary Deaver opening the bag |
+ | Image:DB7_Deaver_panel_110210_csm_2.jpg|Composite electrical panel | ||
+ | Image:DB7_Deaver_panel_110210_csm_3.jpg|Can I wax that electrical panel for you? | ||
+ | Image:DB7_Andrew_Sasha_CAD_110210_csm.jpg|Andrew and Sasha building CAD models of Minibot parts | ||
+ | Image:DB7_Kulick_CAD_110210_csm.jpg|Rich Kulik designing deployment system in CAD | ||
+ | Image:DB7_Deaver_arm_110210_csm_1.jpg|Gary Deaver & ''prime'' with arm | ||
+ | Image:DB7_Deaver_Rizzo_Christopher_110210_csm.jpg|Gary Deaver, Mike Rizzo & Julie Christopher examine DEWBOT's arm | ||
+ | Image:DB7_Molly_cutoff_110210_csm.jpg|Molly cutting off a case-hardened steel shaft with an abraisive Dremel wheel | ||
+ | Image:DB7_Matt_plates_110210_csm.jpg|Matt rough-cutting motor mount plates in bandsaw | ||
+ | Image:DB7_chairman_strategy_session_110210_csm.jpg|Andrew, Sasha, Mike Rizzo, Nicole & Rita Wall in a Chairman's Award discussion. | ||
+ | Image:DB7_lathe_110210_csm.jpg|boring sensor mounting holes with lathe | ||
+ | Image:DB7_Molly_boring_110210_csm.jpg|Molly is boring ''(a concentric 10-32 hole in one end of a 3/8" steel shaft for sensor mounting)'' | ||
+ | Image:DB7_Matt_mill_plates_110210_csm.jpg|Matt milling motor mount plates | ||
+ | Image:DB7_Moyer_Wall_Douglas_110210_csm.jpg|David Moyer, Rita Wall & Douglas with X-bot | ||
+ | Image:DB7_Deaver_arm_110210_csm_2.jpg|Gary Deaver working on claw integration | ||
</gallery> | </gallery> | ||
==Friday February 11, 2011== | ==Friday February 11, 2011== | ||
<gallery widths=250 heights=250 perrow=3> | <gallery widths=250 heights=250 perrow=3> | ||
− | image: | + | image:DB7_McKown_CAD_110211_csm.jpg|Clem McKown dimensioning electrical panel layout drawing |
+ | image:DB7_DJ_Featherman_110211_csm.jpg|DJ & Scott Featherman wiring ''prime'' | ||
+ | image:DB7_Matt_mill_110211_csm_1.jpg|Matt milling arm motor mounts | ||
+ | image:DB7_Matt_doing_the_math_110211_csm.jpg|Matt doing the math | ||
+ | image:DB7_Selina_pc_110211_csm.jpg|Selina cutting polycarbonate for the battery box | ||
+ | image:DB7_Rizzo_DJ_BenR_110211_csm.jpg|Mike Rizzo, DJ & Ben R working on oscillating pivot | ||
+ | image:DB7_Drawing_mill_110211_csm.jpg|Drawing of work hanging below mill control | ||
+ | image:DB7_cutting_mill_110211_csm.jpg|Cutting holes in arm motor mount plates with mill | ||
+ | image:DB7_Matt_mill_110211_csm_2.jpg|Matt milling arm motor mounts | ||
+ | image:DB7_Featherman_Bachmann_Wall_110211_csm.jpg|Scott Featherman, Julie Kulick & Rita Wall | ||
+ | image:DB7_Featherman_Rizzo_Christopher_110211_csm.jpg|Scott Featherman, Mike Rizzo & Julie Christopher | ||
+ | image:DB7_Sasha_Deaver_110211_csm.jpg|Sasha marks electrical panel holes with Gary Deaver | ||
+ | image:DB7_Molly_110211_csm.jpg|Molly cutting polycarbonate | ||
+ | image:DB7_Davis_Molly_110211_csm.jpg|Jon Davis & Molly work on ''V-bot'' | ||
+ | image:DB7_CAD_scissors_110211_csm.jpg|Rich Kulik's CAD model of scizzors | ||
</gallery> | </gallery> | ||
==Saturday February 12, 2011== | ==Saturday February 12, 2011== | ||
<gallery widths=250 heights=250 perrow=3> | <gallery widths=250 heights=250 perrow=3> | ||
− | Image: | + | Image:DB7_Molly_Kellom_design_wheel_110212_csm.jpg|Molly & Ben Kellon designing a minibot wheel |
+ | Image:DB7_wheels_110212_csm.jpg|Molly's minibot wheels | ||
+ | Image:DB7_Alex_110212_csm.jpg|Alex at mill | ||
+ | Image:DB7_electronics panel_110212_csm_1.jpg|Electronics panel for ''prime'' coming together | ||
+ | Image:DB7_electronics panel_110212_csm_2.jpg|ready to begin wiring | ||
+ | Image:DB7_Nichole_Featherman_110212_csm_1.jpg|Nicole & Scott Featherman wiring electronics panel | ||
+ | Image:DB7_Alex_BenR_110212_csm_1.jpg|Alex & Ben R... | ||
+ | Image:DB7_Alex_BenR_110212_csm_2.jpg|...testing autonomous code with ''deux'' | ||
+ | Image:DB7_electronics panel_110212_csm_3.jpg|Electronics panel progressing | ||
+ | Image:DB7_Ian_Deaver_110212_csm.jpg|Ian & Gary Deaver cutting plywood panel for composite claw bars | ||
+ | Image:DB7_Molly_battery_box_110212_csm.jpg|Molly forms a polycarbonate battery box on the heat table... | ||
+ | Image:DB7_battery_box_110212_csm_1.jpg|...folding a flange... | ||
+ | Image:DB7_battery_box_110212_csm_2.jpg|...and using insulation to protect unfolded tabs | ||
+ | Image:DB7_Deaver_carbon_fiber_110212_csm.jpg|Gary Deaver laying up carbon fiber | ||
+ | Image:DB7_Garrison_Ian_epoxy_110212_csm.jpg|Garrison & Ian mixing epoxy | ||
+ | Image:DB7_electronics panel_110212_csm_4.jpg|Battery box on - and some wires | ||
+ | Image:DB7_Kellom_Matt_110212_csm.jpg|Ben Kellon & Matt plan out the milling steps for the next job | ||
+ | Image:DB7_Matt_calipers_110212_csm.jpg|Matt measuring work in progess | ||
+ | Image:DB7_Nichole_Featherman_110212_csm_2.jpg|Nicole & Scott Featherman - finishing up the off-robot panel wiring | ||
+ | Image:DB7_V-bot_110212_csm.jpg|''V-bot'' | ||
+ | Image:DB7_milling_bearing_block_110212_csm.jpg|Milling the bearing block for the Arm Motor Mount | ||
+ | Image:DB7_wiring_110212_csm_1.jpg| | ||
+ | Image:DB7_wiring_110212_csm_2.jpg| | ||
+ | Image:DB7_wiring_110212_csm_3.jpg| | ||
</gallery> | </gallery> | ||
+ | |||
---- | ---- | ||
[[Category:Robot]][[Category:DEWBOT VII]][[Category:DEWBOT VII Build]][[Category:Photo Galleries]] | [[Category:Robot]][[Category:DEWBOT VII]][[Category:DEWBOT VII Build]][[Category:Photo Galleries]] |
Latest revision as of 20:35, 3 April 2011
Contents
Sunday February 6, 2011
Monday February 7, 2011
Carly explaining DEWBOT VII's drive-train to the curious
Tuesday February 8, 2011
Wednesday February 9, 2011
Mike Rizzo liberating a compressor from DEWBOT V