Difference between revisions of "DEWBOT VII Week Six Build Season Photo Gallery"
MaiKangWei (talk | contribs) (→Sunday February 13, 2011) |
MaiKangWei (talk | contribs) (→Wednesday February 16, 2011) |
||
| Line 40: | Line 40: | ||
==Wednesday February 16, 2011== | ==Wednesday February 16, 2011== | ||
<gallery widths=250 heights=250 perrow=3> | <gallery widths=250 heights=250 perrow=3> | ||
| − | Image: | + | Image:DB7_taping_110216_csm.jpg|Faith & Ben B taping the field |
| + | Image:DB7_threading_rod_110216_csm_1.jpg|Threading 3/8" steel rod on the lathe... | ||
| + | Image:DB7_threading_rod_110216_csm_2.jpg|...into the die... | ||
| + | Image:DB7_threading_rod_110216_csm_3.jpg|...and ''viola'', a threaded rod end. | ||
| + | Image:DB7_calibrating_pivots_110216_csm.jpg|Calibrating pivots on ''prime'' | ||
| + | Image:DB7_short_belt_deux_110216_csm.jpg|''Deux'' gats a short (500mm) arm drive belt too | ||
| + | Image:DB7_claw_110216_csm_1.jpg|Claw in position for ground pick-up | ||
| + | Image:DB7_start_position_110216_csm.jpg|Arm in starting position | ||
| + | Image:DB7_belt_guard_detail_110216_csm.jpg|Garrison, Sasha, Molly & Andrew make belt guards | ||
| + | Image:DB7_bumper_detail_110216_csm.jpg|Ben B, Mike Rizzo & Yahya cut pool noodles for bumpers | ||
| + | Image:DB7_claw_110216_csm_2.jpg|Claw extended | ||
| + | Image:DB7_prime_110216_csm.jpg|''Prime'' on field | ||
| + | Image:DB7_Deaver_Weissmam_110216_csm.jpg|Gary Deaver & John Weissman | ||
| + | Image:DB7_belt_guard_110216_csm.jpg|Pivot belt guard | ||
| + | Image:DB7_robots_110216_csm.jpg|''Prime'' & ''deux'' | ||
</gallery> | </gallery> | ||
Revision as of 11:14, 17 February 2011
Contents
Sunday February 13, 2011
Molly and Sasha bend plastic sheet to the amazement and entertainment of visiting students
Deux driving (very well)
Compressor mounted
Arm motor
DJ's Birthday celebration
Composite (plywood, carbon fiber & e-glass) claw bar (a.k.a. triangle)
Prime's mass - including compressor, clippard, solenoids & Claw w/ Claw cylinders (and a 0.4 lbm screwdriver
Siri Maley installing the Claw
Rich Kulik, Siri Maley, Mike Rizzo & Gary Deaver - claw development
Monday February 14, 2011
Molly Wheel on pole
Molly Wheel being assembled
The 2000mm arm drive belt is replaced with a 500mm belt to reduce arm bounce
Faith & Ian (& Garrison) tape the field in preparation for practice
Jack working with Gary Deaver on arm
Molly & Julie Kulik work on V-bot
V-bot at rest
V-bot climbimg...
...past Ben Kellon and to the switch
Tuesday February 15, 2011
Long-range IR sensor - front left
Short-range IR sensor - left front
Gary Deaver & Ben B working on claw development
Julie Christopher & Faith McKown taping field
Programming Team - Michael M, Ben R & DJ
Julie Kulik, Gary Deaver & Scott Featherman working on deux
Arm Angle Sensor Mounts on mill
Short-range IR sensor - left rear
Scott Featherman & Julie Bachmann wiring prime
Wednesday February 16, 2011
Faith & Ben B taping the field
Threading 3/8" steel rod on the lathe...
...into the die...
...and viola, a threaded rod end.
Calibrating pivots on prime
Deux gats a short (500mm) arm drive belt too
Claw in position for ground pick-up
Arm in starting position
Garrison, Sasha, Molly & Andrew make belt guards
Ben B, Mike Rizzo & Yahya cut pool noodles for bumpers
Claw extended
Prime on field
- DB7 Deaver Weissmam 110216 csm.jpg
Gary Deaver & John Weissman
Pivot belt guard
Prime & deux
Thursday February 17, 2011
- DB7 110217 csm 1.jpg
Friday February 18, 2011
- DB7 110218 csm.jpg
Saturday February 19, 2011
- DB7 110219 csm.jpg
