Difference between revisions of "DEWBOT VI Week Four Build Season Photo Gallery"
MaiKangWei (talk | contribs) (→Monday February 1, 2010) |
MaiKangWei (talk | contribs) (→Tuesday February 2, 2010) |
||
| Line 35: | Line 35: | ||
<gallery widths=250 heights=250 perrow=3> | <gallery widths=250 heights=250 perrow=3> | ||
Image:DB6_Groundhog_Phil_2010.jpg|Punxsutawney Phil says that there will be six more weeks of winter, but the robot must ship in three weeks! (AP/Gene J. Puskar) | Image:DB6_Groundhog_Phil_2010.jpg|Punxsutawney Phil says that there will be six more weeks of winter, but the robot must ship in three weeks! (AP/Gene J. Puskar) | ||
| + | Image:DB6_Rizzo_Davis_BenR_discuss_sensor_locations_100202_csm.jpg|Mike Rizzo, Jon Davis & Ben R discuss sensors and their locations | ||
| + | Image:DB6_box-o-pivots_100202_csm.jpg|Assembled Pivots | ||
| + | Image:DB6_Dinesh_Carly_Jen_epanels_100202_csm.jpg|Dinesh, Carly & Jen assemble electrical panels | ||
| + | Image:DB6_epanel_assembly_100202_csm.jpg|Jen, Carly & Dinesh wire panels | ||
| + | Image:DB6_Douglas_Morun_Cole_cutting_square_tube_100202_csm.jpg|Douglas, Mark Morun & Cole cut square tube on the horizontal band saw | ||
| + | Image:DB6_Rizzo_grinding_100202_csm.jpg|Mike Rizzo grinding to eliminate interference | ||
| + | Image:DB6_pivot_test-pass_100202_csm.jpg|Pivot test (pass) | ||
| + | Image:DB6_McKown_Rizzo_last_frame_weld_layout_100202_csm.jpg|Clem McKown & Mike Rizzo laying out work for the final frame welds | ||
| + | Image:DB6_programming_team_100202_csm.jpg|Programming Team at work in the Muppet Lab | ||
| + | Image:DB6_Douglas_Cole_100202_csm.jpg|Douglas & Cole at work on the horizontal band saw | ||
| + | Image:DB6_Matt_welding_100202_csm_1.jpg|Matt welding | ||
| + | Image:DB6_Matt_welding_100202_csm_2.jpg|Matt welding | ||
| + | Image:DB6_Matt_grinding_100202_csm_1.jpg|Matt grinding new welds | ||
| + | Image:DB6_Matt_grinding_100202_csm_2.jpg|Matt grinding new welds | ||
| + | Image:DB6_electrical_components_100202_csm.jpg|Electronics ready for the robot | ||
</gallery> | </gallery> | ||
Revision as of 03:56, 3 February 2010
Contents
Sunday January 31, 2010
welded frame mass
Mass of (blue) bumper set
Siri cutting flange for kicker elastic anchor
Christine cutting the cRIO panel
Christine cutting a Jaguar panel
Mike Rizzo broaching a keyway
Impromptue design review
Impromptue design review
Moyer setting up shop
Pivots in assembly
Christine sanding the Jaguar panel
Jen assembling pivots
Mike Rizzo & Siri riveting pivot plates
Foster planing battery box form
Siri fitting a CIM
Pivot with motor, ready for wiring
Pivots on chassis
Monday February 1, 2010
Ben W cutting replacement Jaguar panel
Mark Morun making fine adjustments to pivot parts
Cole, Julie Bachmann & Matt
Cole, Julie Bachmann & Matt hard at work
Douglas & Ben W breaking chain for the pivots
Julie Bachmann & Ben W working on Jaguar panel
The left Jaguar panel clamped into place
Tuesday February 2, 2010
Punxsutawney Phil says that there will be six more weeks of winter, but the robot must ship in three weeks! (AP/Gene J. Puskar)
Mike Rizzo, Jon Davis & Ben R discuss sensors and their locations
Assembled Pivots
Dinesh, Carly & Jen assemble electrical panels
Jen, Carly & Dinesh wire panels
Douglas, Mark Morun & Cole cut square tube on the horizontal band saw
Mike Rizzo grinding to eliminate interference
Pivot test (pass)
Clem McKown & Mike Rizzo laying out work for the final frame welds
Programming Team at work in the Muppet Lab
Douglas & Cole at work on the horizontal band saw
Matt welding
Matt welding
Matt grinding new welds
Matt grinding new welds
Electronics ready for the robot
