Difference between revisions of "FTC 7314 Engineering Notebook 2014-10-13"
From DEW Robotics
(Created page with '=='''Competition Season Meeting'''== <!-- This is the meeting information table --> {|border=1 cellpadding="10" !Meeting Date !!Meeting Time !!Location !!Attendees |- | | |TCH...') |
(→Competition Season Meeting) |
||
Line 5: | Line 5: | ||
!Meeting Date !!Meeting Time !!Location !!Attendees | !Meeting Date !!Meeting Time !!Location !!Attendees | ||
|- | |- | ||
− | | | + | |10/14/2014 |
− | | | + | |6pm-9pm |
|TCHS Brandywine | |TCHS Brandywine | ||
− | | | + | |Braden, Trevor, Josh Justin, Nick, Laura, Ahkila, CJ, |
|} | |} | ||
Line 19: | Line 19: | ||
| '''Braden and Trevor worked on moving and finishing the electronics on the prototype chassie ''' | | '''Braden and Trevor worked on moving and finishing the electronics on the prototype chassie ''' | ||
| | | | ||
− | * | + | * We were able to complete it and program it to do what we wanted it to do. Then we were able to test it out. |
|- | |- | ||
|- | |- | ||
| '''80-20 for linear slide''' | | '''80-20 for linear slide''' | ||
| | | | ||
− | * Josh, Justin and mentor Andrew finished the slider pieces that connect to the 80-20 and allow the 80-20 to slide up and down. | + | * Josh, Justin and mentor Andrew finished the slider pieces that connect to the 80-20 and allow the 80-20 to slide up and down. |
+ | * We also set up for the rollers inside the sliders by preparing the mill for the next robotics meeting. | ||
|- | |- | ||
− | |''' | + | |'''Prototyping the Drum Shooter''' |
| | | | ||
− | *Nick talked with mentors, and Laura about the design and prototype of the | + | * Nick talked with mentors, and Laura about the design and prototype of the drum shooter. |
− | + | * Following problems with the initial design from the previous week, we look into new ideas. | |
+ | * The idea for tonight's meeting was that we would have a spring below the center point of the drum shooter so that when a roller (which is located near the outside of the wheel) would move over the spring there would be tension against it. After the roller has been pushed 90 degrees the tension will then move the roller, and wheel, with exceeding force, therefore throwing the ball. | ||
+ | * Cj helped with the testing of the wheel. He had to relocate the bars that attached the offensive wheel. | ||
+ | * When we tested the new drum shooter, it did not work any better than the previous drum shooter, still only reaching about 2 feet. | ||
+ | * To add more height, we moved the spring closer to the center point, and pre-tensioned the spring more. | ||
+ | * The results were outstanding! It shot what we believed to be high enough, almost hitting the ceiling when launched off a table. It also shot both small and big balls remarkably well. | ||
+ | * Next meeting, we will add a motor to the prototype. For today, we only pushed the wheel with our hands. We will very likely need to gear the motor down, because it will take a lot of torque to tension that spring. We are also planning on trying to shoot the ball through a tube, and see if the ball will loose speed when hitting the side of the tube. | ||
+ | * We made a lot of progress, and it looks like the drum shooter will be an effective lift, if the motor can tension the spring. | ||
+ | |} | ||
<br /> | <br /> | ||
− | |||
<!-- This is the footer for a meeting entry --> | <!-- This is the footer for a meeting entry --> | ||
{| border=1 width=100% <!-- s are needed to create blank space in HTML --> | {| border=1 width=100% <!-- s are needed to create blank space in HTML --> | ||
Line 40: | Line 48: | ||
|- <!-- <br />s are needed to create line breaks for empty lines in HTML --> | |- <!-- <br />s are needed to create line breaks for empty lines in HTML --> | ||
|<br /><br /> | |<br /><br /> | ||
− | |<br /><br /> | + | |<br /><br /> |
|<br /><br /> | |<br /><br /> | ||
|<br /><br /> | |<br /><br /> | ||
|} | |} |
Revision as of 04:48, 14 October 2014
Competition Season Meeting
Meeting Date | Meeting Time | Location | Attendees |
---|---|---|---|
10/14/2014 | 6pm-9pm | TCHS Brandywine | Braden, Trevor, Josh Justin, Nick, Laura, Ahkila, CJ, |
Tasks | Reflections |
---|---|
Braden and Trevor worked on moving and finishing the electronics on the prototype chassie |
|
80-20 for linear slide |
|
Prototyping the Drum Shooter |
|
Recorded by: | Date: | Journal Editor: | Date: |
---|---|---|---|