Search results
From DEW Robotics
Create the page "LaTeX" on this wiki! See also the search results found.
- ::* (5) 3/8" OD latex tube "cords" ...eter and grooved with (5) 3/8" diameter semicircular grooves to engage the latex tube "cords". Roller material is Nylon / Molybdenum disulfide composite.6 KB (924 words) - 14:08, 20 September 2009
- * Learn how to join latex tube ends to make ball lift cords2 KB (321 words) - 23:42, 23 August 2009
- ...with the ball. While the immediate kicking force is provided by tensioned latex tubing, pneumatic cylinders are used to tension (cock), latch and fire the28 KB (4,351 words) - 20:29, 15 September 2012
- :*But the latex tubing kicker is a trooper29 KB (4,611 words) - 13:35, 23 February 2010
- :The Kicker is latex-tubing powered. Kicker is 15” wide and had a kicking face tangent to the ...ylinder retracts, opening the Latch and releasing the energy stored in the latex springs.14 KB (2,202 words) - 14:21, 12 July 2011
- :*The latex tubing wears out occasionally. The pit checks routinely for signs of wear :*...but late on Saturday all (5) latex tube passes failed simultaneously (or nearly so). Analysis of the sheared15 KB (2,463 words) - 13:37, 13 June 2010
- ...possessor_Deaver_100325_csm.jpg|''Possessor'' & Gary Deaver installing new latex springs13 KB (1,840 words) - 16:25, 21 December 2010
- ...ex_100221_csm.jpg|Gary Deaver & Clem McKown replace the ''possessor'' with latex tubing5 KB (844 words) - 20:41, 27 February 2010
- ...nt of the) frame perimeter. When the mirror was mounted, I considered the latex spring a cheesy, temporary expedience. In retrospect, it is a highly-effec11 KB (1,807 words) - 16:26, 7 November 2010
- :* Installed ½" ID latex tubing on bottom rod in lieu of friction tape ...in fact, it was in the functional specs), we'd rather have it up. A second latex tube has been added to the other side to prevent torquing.24 KB (3,796 words) - 01:06, 10 August 2011
- :* latex tubing seems to make an effective arm balance23 KB (3,294 words) - 22:53, 21 March 2011
- (5) wraps of 1/2" OD x 1/8" ID latex surgical tubing between the upper column link and the lower claw link provi13 KB (2,000 words) - 02:28, 12 July 2011
- ...r band treads, these fell off easily and were replaced with large-diameter latex surgical tubing treads. ...eduction is provided to the two motors. This reduction is achieved with a latex wheel driving an aluminum wheel and slippage at this point should the minib11 KB (1,719 words) - 15:57, 24 October 2011
- ...F16] absolute encoder angle sensor. The flexible connector was originally latex tubing, but later changed to a fiberglass flexible coupling (GJ-6D from Aut12 KB (1,824 words) - 00:23, 7 September 2012
- ...1/16" bore x 4" stroke pneumatic cylinder. The rear leg is held down by a latex spring and is raised passively by the pyramid corner when the robot drives10 KB (1,601 words) - 21:55, 3 January 2014
- ***Latex tubing "springs" can assist lift once shafts are secured3 KB (401 words) - 03:23, 9 September 2014
- ...ul catapult and slingshot prototypes were built and tested. Both utilized latex tubing as springs. the catapult had the advantage of being able to make si From the first concept, the slingshot consisted of a pair of elastic latex tubing loops crossing at approximately 90. A 2" PVC pipe and pipe cap asse10 KB (1,546 words) - 14:26, 15 November 2014
- ...be via a machined aluminum clamp. The cylinder extension is assisted by a latex tubing tension spring. ..., this cord extends the fiberglass hook so that it engages the RC. A 1/8" latex cord spring on the opposite side of the fiberglass hook pivot prevents the4 KB (692 words) - 01:44, 30 May 2015
- Immediate modifications were the addition of latex elastics to assist the raising of the Portcullis Arm and camera mounts.5 KB (764 words) - 22:58, 13 May 2016
