Search results
From DEW Robotics
Create the page "Time" on this wiki! See also the search results found.
- !Meeting Date !!Meeting Time !!Location !!Attendees2 KB (269 words) - 21:44, 15 January 2015
- !Meeting Date !!Meeting Time !!Location !!Attendees3 KB (447 words) - 21:46, 14 January 2015
- !Meeting Date !!Meeting Time !!Location !!Attendees * Instead of replacing the clutch every time it wore down, Laura decided to try to write a software clutch.2 KB (263 words) - 23:26, 15 January 2015
- !Meeting Date !!Meeting Time !!Location !!Attendees2 KB (265 words) - 23:54, 15 January 2015
- ...Edgetech as sponsor, we redesigned our swerve module to reduce the machine time requirements and to bring as much of the machining in-house as practical. ...ure, we revised the pivot design with an objective of reducing the machine time required to produce these, making the following changes:5 KB (768 words) - 14:59, 20 September 2015
- ...le NJ. 1640's second qualifier for the 2015 season and our 3<sup>rd</sup> time at the Seneca (a.k.a. Lenape-Seneca) MAR Qualifier.5 KB (782 words) - 22:55, 20 April 2015
- ...nd chains. All new parts were employed, not splices. This change-out was time-consuming. The shorter lift had required us to back the robot up from the5 KB (865 words) - 02:06, 21 April 2015
- ...Step RCs will almost certainly win the match. It's also obvious that the time to gain control of the Step RCs is at the very start of the match; the firs ...striking the RC. By reducing flexure, the bounce is reduced and therefore time before driving backwards also reduced.4 KB (692 words) - 01:44, 30 May 2015
- ...rks Professional Exam, which covers slightly more material at a much lower time limit.5 KB (748 words) - 17:09, 25 July 2015
- ...reducing the probability of it landing on end (recoverable, but a waste of time). ...'s travel and so these rods are constrained by the stacker and at the same time do not constrain the stacker lift's travel.6 KB (942 words) - 13:31, 5 July 2015
- But different is what we do. It's what we are. At least we think so. Time to put that to the test! ...t the Westtown School) and 1640 and was a huge success. This was the first time the two teams had worked together to host a robotics tournament. According12 KB (1,832 words) - 01:35, 6 May 2017
- ...in 2008 (with a [[DEWBOT IV Duel on the Delaware | terrible robot]]) and 4-time winners in [[DEWBOT VII Duel on the Delaware | 2011]], [[DEWBOT VIII Duel o ...drive team, with a special fedoras-off to first-time driver Abbi and first-time human player Kevin! Thanks to Ian, who took on the challenging lead scout j2 KB (403 words) - 23:01, 18 October 2015
- *FRC Qualifier w/ Metal Moose – unknown at time3 KB (402 words) - 21:54, 4 August 2015
- ...with the FLL scrimmage. We do not have the people to do both at the same time. We resolved to shift the date to 28-November (but this date is unavailabl1 KB (192 words) - 01:14, 19 August 2015
- :First time at Worlds! The team finished 17<sup>th</sup> in Franklin Division.6 KB (905 words) - 21:45, 10 June 2016
- !Meeting Date !!Meeting Time !!Location !!Attendees * After all the pre presentations were over, it was time for the game reveal! There was a real sense of suspense in the room as we c5 KB (820 words) - 19:38, 27 November 2015
- !Meeting Date !!Meeting Time !!Location !!Team Members in Attendance: ...tonomous scenarios. It's always great fun, and allows us to gauge how much time will be needed for each scenario. We're clocking in at a little less than t4 KB (748 words) - 23:20, 27 November 2015
- !Meeting Date !!Meeting Time !!Location !!Attendees ...to the legacy module went bad. There had been connection issues the entire time, but initially, just disconnecting and reconnecting would work. Toward the5 KB (781 words) - 06:12, 4 December 2015
- !Meeting Date !!Meeting Time !!Location !!Attendees ...esign for an intake that involved a box that lifts 1 piece of debris at at time on a vertical conveyor belt.4 KB (671 words) - 02:45, 30 November 2015
- !Meeting Date !!Meeting Time !!Location !!Attendees ...treads. They put the rubber tread grips into the treads. This took a long time and Gary reported that his arm ached after he slid all the pieces into thei3 KB (374 words) - 03:12, 30 November 2015